共计 23171 个字符，预计需要花费 58 分钟才能阅读完成。
- 文章假设读者肯定水平理解 linux 基础知识
- 文章来源于《嵌入式 linux 齐全开发手册》- IMX6ull 开发板从零移植篇
区别在于: 本文形容从各个网站（官网）下载最新 ubuntu、穿插编译器、uboot、kernel、buildroot 从零开始构建，更靠近理论工程环境
(可同时穿插参阅两份文章)一、对于 ubuntu
- 下载安装最新桌面 LTS 版本 ubuntu
- 失常步骤装置（参考网络其它文章）
-
几个要害的设置
- 磁盘大小：60GB 以上
- 网络连接：应用桥接网络（复制网络连接状态）[路由器连贯开发板和电脑]
二、对于穿插工具链
1、下载
ARM 开发者核心下载穿插编译工具链
host 为 linux 👉 `x86_64 linux`
imx6ul 为 arm_A7 架构 👉 `AArch32`
imx6ul 反对硬件浮点 👉 `hard fllat`
需反对 linux 操作系统 👉 `none-linux`2、配置
解压缩
tiansong@tiansong:~/100ask_imx6ull_pro$ ls
arm-gnu-toolchain-11.3.rel1-x86_64-arm-none-linux-gnueabihf.tar.xz
tiansong@tiansong:~/100ask_imx6ull_pro$ tar -xvf arm-gnu-toolchain-11.3.rel1-x86_64-arm-none-linux-gnueabihf.tar.xz
tiansong@tiansong:~/100ask_imx6ull_pro$ ls
arm-gnu-toolchain-11.3.rel1-x86_64-arm-none-linux-gnueabihf arm-gnu-toolchain-11.3.rel1-x86_64-arm-none-linux-gnueabihf.tar.xz设置环境变量
tiansong@tiansong:~$ vim ~/.bashrc
# 在文件开端追加
export ARCH=arm
export CROSS_COMPILE=arm-none-linux-gnueabihf-
export PATH=$PATH:/home/tiansong/100ask_imx6ull_pro/arm-gnu-toolchain-11.3.rel1-x86_64-arm-none-linux-gnueabihf/bin
# 使环境变量在以后终端失效
tiansong@tiansong:~/100ask_imx6ull_pro$ source ~/.bashrc验证是否配置胜利
tiansong@tiansong:~/100ask_imx6ull_pro$ arm-none-linux-gnueabihf-gcc -v
Using built-in specs.
COLLECT_GCC=arm-none-linux-gnueabihf-gcc
COLLECT_LTO_WRAPPER=/home/tiansong/100ask_imx6ull_pro/arm-gnu-toolchain-11.3.rel1-x86_64-arm-none-linux-gnueabihf/bin/../libexec/gcc/arm-none-linux-gnueabihf/11.3.1/lto-wrapper
Target: arm-none-linux-gnueabihf
Configured with: /data/jenkins/workspace/GNU-toolchain/arm-11/src/gcc/configure --target=arm-none-linux-gnueabihf --prefix= --with-sysroot=/arm-none-linux-gnueabihf/libc --with-build-sysroot=/data/jenkins/workspace/GNU-toolchain/arm-11/build-arm-none-linux-gnueabihf/install//arm-none-linux-gnueabihf/libc --with-bugurl=https://bugs.linaro.org/ --enable-gnu-indirect-function --enable-shared --disable-libssp --disable-libmudflap --enable-checking=release --enable-languages=c,c++,fortran --with-gmp=/data/jenkins/workspace/GNU-toolchain/arm-11/build-arm-none-linux-gnueabihf/host-tools --with-mpfr=/data/jenkins/workspace/GNU-toolchain/arm-11/build-arm-none-linux-gnueabihf/host-tools --with-mpc=/data/jenkins/workspace/GNU-toolchain/arm-11/build-arm-none-linux-gnueabihf/host-tools --with-isl=/data/jenkins/workspace/GNU-toolchain/arm-11/build-arm-none-linux-gnueabihf/host-tools --with-arch=armv7-a --with-fpu=neon --with-float=hard --with-mode=thumb --with-arch=armv7-a --with-pkgversion='Arm GNU Toolchain 11.3.Rel1'
Thread model: posix
Supported LTO compression algorithms: zlib
gcc version 11.3.1 20220712 (Arm GNU Toolchain 11.3.Rel1)三、对于 uboot
1、下载
# 下载
tiansong@tiansong:~/100ask_imx6ull_pro$ tiansong@tiansong:~/100ask_imx6ull_pro$ git clone https://source.codeaurora.cn/external/imx/uboot-imx
tiansong@tiansong:~/100ask_imx6ull_pro$ ls
arm-gnu-toolchain-11.3.rel1-x86_64-arm-none-linux-gnueabihf uboot-imx
# 查看仓库所有分支
tiansong@tiansong:~/100ask_imx6ull_pro$ cd uboot-imx/
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ git branch -a
...
remotes/origin/imx_v2020.04_5.4.70_2.3.0
...
# 切换到 imx 最新分支
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ git checkout remotes/origin/imx_v2020.04_5.4.70_2.3.0
Updating files: 100% (11834/11834), done.
Note: switching to 'remotes/origin/imx_v2020.04_5.4.70_2.3.0'.
You are in 'detached HEAD' state. You can look around, make experimental
changes and commit them, and you can discard any commits you make in this
state without impacting any branches by switching back to a branch.
If you want to create a new branch to retain commits you create, you may
do so (now or later) by using -c with the switch command. Example:
git switch -c <new-branch-name>
Or undo this operation with:
git switch -
Turn off this advice by setting config variable advice.detachedHead to false
HEAD is now at 62a81128c0 MLK-25878: imx8: scu: Increase sendmsg timeout for SCFW MU
# 确认是否却换胜利
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ git log -1
commit 62a81128c07c3efc123039f796ffc43b4eacbf04 (HEAD, origin/imx_v2020.04_5.4.70_2.3.0)
Author: Nitin Garg <nitin.garg@nxp.com>
Date: Fri Apr 29 10:54:20 2022 -0500
MLK-25878: imx8: scu: Increase sendmsg timeout for SCFW MU
Similar to receivemsg, sendmsg function should also
use 1 sec timeout for MU communication with SCFW.
Signed-off-by: Nitin Garg <nitin.garg@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>2、开发板文件适配
前置阐明：有多处关联，移植尽量一口气实现
默认的配置文件
复制公板提供的默认配置文件
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ cd configs/
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/configs$ ls *mx6ull_14x14_evk* -l
-rw-rw-r-- 1 tiansong tiansong 1988 8 月 26 10:36 mx6ull_14x14_evk_defconfig # imx6ullevk 公板默认的配置文件，默认只反对 SD 卡启动
-rw-rw-r-- 1 tiansong tiansong 1963 8 月 26 10:36 mx6ull_14x14_evk_emmc_defconfig # imx6ull 反对 emmc 启动形式启动的配置文件
-rw-rw-r-- 1 tiansong tiansong 2095 8 月 26 10:36 mx6ull_14x14_evk_nand_defconfig # imx6ull 反对 nand 启动形式启动的配置文件
-rw-rw-r-- 1 tiansong tiansong 2007 8 月 26 10:36 mx6ull_14x14_evk_optee_defconfig # imx6ull 反对 optee 零碎的配置文件
-rw-rw-r-- 1 tiansong tiansong 1958 8 月 26 10:36 mx6ull_14x14_evk_plugin_defconfig # imx6ull 反对扩大性能的配置文件，次要是烧写性能
-rw-rw-r-- 1 tiansong tiansong 2057 8 月 26 10:36 mx6ull_14x14_evk_qspi1_defconfig # imx6ull 反对扩大性能的配置文件，次要是烧写性能
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/configs$ cp mx6ull_14x14_evk_emmc_defconfig 100ask_imx6ull_pro_emmc_defconfig
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/configs$ ls 100ask_imx6ull_pro_emmc_defconfig -l
-rw-rw-r-- 1 tiansong tiansong 1982 8 月 26 10:54 100ask_imx6ull_pro_emmc_defconfig批改复制的配置文件（三处）
CONFIG_TARGET_MX6ULL_14X14_EVK=y
👉
CONFIG_TARGET_100ASK_IMX6ULL_PRO_EMMC=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ullevk/imximage.cfg"
👉
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/100ask/100ask_imx6ull_pro_emmc/imximage.cfg"
CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-evk-emmc"
👉
CONFIG_DEFAULT_DEVICE_TREE="100ask_imx6ull_pro_emmc"板件级反对
头文件
复制公板提供的
.h文件
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ cd include/configs/
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ cd include/configs/
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/include/configs$ cp mx6ullevk.h 100ask_imx6ull_pro_emmc.h批改复制的
.h文件（两处）
#ifndef __MX6ULLEVK_CONFIG_H
#define __MX6ULLEVK_CONFIG_H
👉
#ifndef __100ASK_IMX6ULL_PRO_EMMC_CONFIG_H
#define __100ASK_IMX6ULL_PRO_EMMC_CONFIG_H文件夹
复制公板提供的文件夹
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ cd board/
# 创立二级目录，100ask 族和 100ask_imx6ull_pro_emmc 族
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/board$ mkdir 100ask
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/board$ mkdir 100ask/100ask_imx6ull_pro_emmc
# 复制 common 文件夹
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/board$ cp freescale/common 100ask/
# 复制 freescale/mx6ullevk/* 下所有公板文件
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/board$ cp freescale/mx6ullevk/* 100ask/100ask_imx6ull_pro_emmc/
# 查看文件数，确认是否操作胜利
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/board$ cd 100ask/
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/board/100ask$ tree
.
├── 100ask_imx6ull_pro_emmc # 重视批改！！│ ├── 100ask_imx6ull_pro_emmc.c
│ ├── built-in.o
│ ├── imximage.cfg
│ ├── imximage_lpddr2.cfg
│ ├── Kconfig
│ ├── MAINTAINERS
│ ├── Makefile
│ ├── plugin.S
│ └── README
└── common
├── arm_sleep.c
├── built-in.o
├── cadmus.c
├── cadmus.h
├── cds_pci_ft.c
├── cds_via.c
...
...
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/board/100ask$ cd 100ask_imx6ull_pro_emmc/复制
mx6ullevk.c
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/board/freescale/mx6ullevk$ cp mx6ullevk.c 100ask_imx6ull_pro_emmc.c 批改
Makefile
obj-y := 100ask_imx6ull_pro_emmc.o批改
Kconfig
if TARGET_100ASK_IMX6ULL_PRO_EMMC # 留神与 100ask_imx6ull_pro_emmc_defconfig 中 CONFIG_TARGET_100ASK_IMX6ULL_PRO_EMMC=y 对应
config SYS_BOARD
default "100ask_imx6ull_pro_emmc" # 100ask_imx6ull_pro_emmc 留神与后续多处对应
config SYS_VENDOR
default "100ask"
config SYS_CONFIG_NAME
default "100ask_imx6ull_pro_emmc"
config SYS_TEXT_BASE
default 0x87800000
endif批改
MAINTAINERS【留神门路填写正确】
MX6ULLEVK BOARD
M: Peng Fan <peng.fan@nxp.com>
S: Maintained
F: board/100ask/100ask_imx6ull_pro_emmc/
F: include/configs/100ask_imx6ull_pro.h
F: configs/100ask_imx6ull_pro_emmc_defconfig批改
imximage.cfg
PLUGIN board/freescale/mx6ullevk/plugin.bin 0x00907000
👉
PLUGIN board/100ask/100ask_imx6ull_pro_emmc/plugin.bin 0x00907000批改
imximage_lpddr2.cfg
PLUGIN board/freescale/mx6ullevk/plugin.bin 0x00907000
👉
PLUGIN board/100ask/100ask_imx6ull_pro_emmc/plugin.bin 0x00907000减少图像化反对
批改
/home/tiansong/100ask_imx6ull_pro/uboot-imx/arch/arm/mach-imx/mx6/Kconfig【留神门路】
config TARGET_MX6ULL_14X14_EVK
bool "Support mx6ull_14x14_evk"
select BOARD_LATE_INIT
select DM
select DM_THERMAL
select MX6ULL
imply CMD_DM
# 在 TARGET_MX6ULL_14X14_EVK 之下增加，留神与 100ask_imx6ull_pro_emmc_defconfig 中 CONFIG_TARGET_100ASK_IMX6ULL_PRO_EMMC=y 对应
config TARGET_100ASK_IMX6ULL_PRO_EMMC
bool "Support 100ask_imx6ull_pro_emmc"
select BOARD_LATE_INIT
select DM
select DM_THERMAL
select MX6ULL
imply CMD_DM
# 文件开端增加，留神门路
source "board/100ask/100ask_imx6ull_pro_emmc/Kconfig"默认的设施树
复制公板设施树文件
imx6ull-14x14-evk-emmc.dts
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/arch/arm/dts$ pwd
/home/tiansong/100ask_imx6ull_pro/uboot-imx/arch/arm/dts
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/arch/arm/dts$ ls imx6ull-14x14-evk* -l
-rw-rw-r-- 1 tiansong tiansong 407 8 月 26 10:36 imx6ull-14x14-evk.dts
-rw-rw-r-- 1 tiansong tiansong 570 8 月 26 10:36 imx6ull-14x14-evk-emmc.dts
-rw-rw-r-- 1 tiansong tiansong 1184 8 月 26 10:36 imx6ull-14x14-evk-gpmi-weim.dts
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx/arch/arm/dts$ cp imx6ull-14x14-evk-emmc.dts 100ask_imx6ull_pro_emmc.dts编辑设施树文件
100ask_imx6ull_pro_emmc.dts
# 察看 100ask_imx6ull_pro_emmc.dts 文件内容，依赖于 imx6ull-14x14-evk.dts
#include "imx6ull-14x14-evk.dts"
# 察看 imx6ull-14x14-evk.dts，依赖于多个文件
#include "imx6ull.dtsi"
#include "imx6ul-14x14-evk.dtsi"
#include "imx6ul-14x14-evk-u-boot.dtsi"- 交融
100ask_imx6ull_pro_emmc.dts、imx6ull-14x14-evk.dts和imx6ul-14x14-evk.dtsi到100ask_imx6ull_pro_emmc.dts - 批改
lcd 和 phy设施树参数 - 以下为批改好的设施树：
/*
* Copyright 2019 NXP
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
*/
/dts-v1/;
#include "imx6ull.dtsi"
/ {
model = "i.MX6 ULL 14x14 EVK Board";
compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull";
aliases {spi5 = &{/spi4};
};
chosen {stdout-path = &uart1;};
memory@80000000 {
device_type = "memory";
reg = <0x80000000 0x20000000>;
};
reg_sd1_vmmc: regulator-sd1-vmmc {
compatible = "regulator-fixed";
regulator-name = "VSD_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
off-on-delay-us = <20000>;
enable-active-high;
};
reg_can_3v3: regulator-can-3v3 {
compatible = "regulator-fixed";
regulator-name = "can-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio_spi 3 GPIO_ACTIVE_LOW>;
};
spi4 {
compatible = "spi-gpio";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi4>;
status = "okay";
pinctrl-assert-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
gpio-sck = <&gpio5 11 0>;
gpio-mosi = <&gpio5 10 0>;
cs-gpios = <&gpio5 7 0>;
num-chipselects = <1>;
#address-cells = <1>;
#size-cells = <0>;
gpio_spi: gpio@0 {
compatible = "fairchild,74hc595";
gpio-controller;
#gpio-cells = <2>;
reg = <0>;
registers-number = <1>;
registers-default = /bits/ 8 <0x57>;
spi-max-frequency = <100000>;
};
};
// 新增背光管制节点
backlight {
compatible = "pwm-backlight";
pwms = <&pwm1 0 1000>;
brightness-levels = <0 1 2 3 4 5 6 8 10>;
default-brightness-level = <8>;
status = "okay";
};
};
&clks {
assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
assigned-clock-rates = <786432000>;
};
&i2c2 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
codec: wm8960@1a {
#sound-dai-cells = <0>;
compatible = "wlf,wm8960";
reg = <0x1a>;
wlf,shared-lrclk;
};
};
&fec1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet1>;
phy-mode = "rmii";
phy-handle = <ðphy0>;
status = "disabled"; // 网口 1 未应用，状态禁用
};
&fec2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet2>;
phy-mode = "rmii";
phy-handle = <ðphy1>;
phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>; // 减少复位
phy-reset-duration = <25>; // 复位持续时间
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
ethphy0: ethernet-phy@2 {
reg = <0>;
smsc,led-mode = <1>;
clocks = <&clks IMX6UL_CLK_ENET_REF>;
clock-names = "rmii-ref";
};
ethphy1: ethernet-phy@1 {
reg = <1>; // phy 地址
smsc,led-mode = <1>;
clocks = <&clks IMX6UL_CLK_ENET2_REF>;
clock-names = "rmii-ref";
};
};
};
&can1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan1>;
xceiver-supply = <®_can_3v3>;
status = "okay";
};
&can2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flexcan2>;
xceiver-supply = <®_can_3v3>;
status = "okay";
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
status = "okay";
mag3110@e {
compatible = "fsl,mag3110";
reg = <0x0e>;
};
};
&lcdif {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_lcdif_dat
&pinctrl_lcdif_ctrl>;
display = <&display0>;
status = "okay";
reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; // 减少复位
display0: display@0 {
bits-per-pixel = <24>;
bus-width = <24>;
display-timings { // 时许调整
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <50000000>;
hactive = <1024>;
vactive = <600>;
hfront-porch = <160>;
hback-porch = <140>;
hsync-len = <20>;
vback-porch = <20>;
vfront-porch = <12>;
vsync-len = <3>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <1>;
pixelclk-active = <0>;
};
};
};
};
&pwm1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm1>;
status = "okay";
};
&qspi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_qspi>;
status = "okay";
flash0: n25q256a@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "micron,n25q256a", "jedec,spi-nor";
spi-max-frequency = <29000000>;
reg = <0>;
};
};
&sai2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sai2>;
assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
<&clks IMX6UL_CLK_SAI2>;
assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
assigned-clock-rates = <0>, <12288000>;
fsl,sai-mclk-direction-output;
status = "okay";
};
&snvs_poweroff {status = "okay";};
&tsc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tsc>;
xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
measure-delay-time = <0xffff>;
pre-charge-time = <0xfff>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
uart-has-rtscts;
status = "okay";
};
&usbotg1 {
dr_mode = "otg";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb_otg1>;
status = "okay";
};
&usbotg2 {
dr_mode = "host";
disable-over-current;
status = "okay";
};
&usbphy1 {fsl,tx-d-cal = <106>;};
&usbphy2 {fsl,tx-d-cal = <106>;};
&usdhc1 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>;
pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
keep-power-in-suspend;
wakeup-source;
vmmc-supply = <®_sd1_vmmc>;
status = "okay";
};
&usdhc2 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc2_8bit>;
pinctrl-1 = <&pinctrl_usdhc2_8bit_100mhz>;
pinctrl-2 = <&pinctrl_usdhc2_8bit_200mhz>;
bus-width = <8>;
non-removable;
status = "okay";
};
&wdog1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdog>;
fsl,ext-reset-output;
};
&iomuxc {
pinctrl-names = "default";
pinctrl_csi1: csi1grp {
fsl,pins = <
MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088
MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088
MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088
MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088
MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088
MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088
MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088
MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088
MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088
>;
};
pinctrl_enet1: enet1grp {
fsl,pins = <
MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
>;
};
pinctrl_enet2: enet2grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031
/* used for pht reset */
MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x79
>;
};
pinctrl_flexcan1: flexcan1grp{
fsl,pins = <
MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020
MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020
>;
};
pinctrl_flexcan2: flexcan2grp{
fsl,pins = <
MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
>;
};
pinctrl_i2c1_gpio: i2c1grp_gpio {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
>;
};
pinctrl_lcdif_dat: lcdifdatgrp {
fsl,pins = <
MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79
MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79
MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79
MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79
MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79
MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79
>;
};
pinctrl_lcdif_ctrl: lcdifctrlgrp {
fsl,pins = <
MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
/* used for lcd reset */
MX6UL_PAD_LCD_RESET__GPIO3_IO04 0x1b0b0
>;
};
pinctrl_qspi: qspigrp {
fsl,pins = <
MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
>;
};
pinctrl_sai2: sai2grp {
fsl,pins = <
MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088
MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088
MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088
MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088
MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088
MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x17059
>;
};
pinctrl_pwm1: pwm1grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
>;
};
pinctrl_sim2: sim2grp {
fsl,pins = <
MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD 0xb808
MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK 0x31
MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B 0xb808
MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN 0xb808
MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD 0xb809
MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x3008
>;
};
pinctrl_spi4: spi4grp {
fsl,pins = <
MX6UL_PAD_BOOT_MODE0__GPIO5_IO10 0x70a1
MX6UL_PAD_BOOT_MODE1__GPIO5_IO11 0x70a1
MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x70a1
MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x80000000
>;
};
pinctrl_tsc: tscgrp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1
MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1
MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1
MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1
>;
};
pinctrl_usb_otg1: usbotg1grp {
fsl,pins = <
MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
>;
};
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */
MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */
MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */
>;
};
pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
>;
};
pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
fsl,pins = <
MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17059
MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
>;
};
pinctrl_usdhc2_8bit: usdhc2grp_8bit {
fsl,pins = <
MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
>;
};
pinctrl_usdhc2_8bit_100mhz: usdhc2grp_8bit_100mhz {
fsl,pins = <
MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170b9
MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170b9
MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170b9
MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170b9
>;
};
pinctrl_usdhc2_8bit_200mhz: usdhc2grp_8bit_200mhz {
fsl,pins = <
MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
>;
};
pinctrl_wdog: wdoggrp {
fsl,pins = <
MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
>;
};
};- 留神
backlight为新减少节点，用于 lcd 背光管制 - 留神
fec1节点，批改为禁用 - 留神
fec2节点，减少复位反对，SMSC 反对 - 留神
lcdif节点，批改复位反对，批改屏幕控制器时许 - 留神
usdhc2节点，来自于imx6ull-14x14-evk-emmc.dts - 留神
pinctrl_enet2节点，MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x79 - 留神
pinctrl_lcdif_ctrl节点，MX6UL_PAD_LCD_RESET__GPIO3_IO04 0x1b0b0
批改
/home/tiansong/100ask_imx6ull_pro/uboot-imx/drivers/net/phy/phy.c
int genphy_config_aneg(struct phy_device *phydev)
{
int result;
phy_reset(phydev); // 新增
if (phydev->autoneg != AUTONEG_ENABLE)
return genphy_setup_forced(phydev);
result = genphy_config_advert(phydev);
// ...
}3、配置及编译
装置环境依赖
sudo apt install make
sudo apt install bison flex生成 .config 文件
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ pwd
/home/tiansong/100ask_imx6ull_pro/uboot-imx
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ make 100ask_imx6ull_pro_emmc_defconfig图像化配置
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ make menuconfig确认板级反对, 目录项
ARM architecture
确认默认的设施树，目录项
Boot media–>Device Tree Control
使能
SD/EMMC启动, 目录项Boot media
使能随机
MAC地址生成, 目录项Networking support
网卡反对
- 目录项
Device Drivers/Network device support
- 目录项
Device Drivers/Ethernet PHY(physical media interface) support
编译
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ make -j12
tiansong@tiansong:~/100ask_imx6ull_pro/uboot-imx$ ls u-boot-dtb.imx
u-boot-dtb.imx提交批改到本地仓库
正文完
