乐趣区

关于算法:ELE00107M编程技术分析

ELE00107M Resit
Department of Electronic Engineering
Resit Assessments 2021/22
ELE00107M
C Programming for MSc
This component (Reassessment: Assignment) contribute 100% of the resit assessment for this
module:
Clearly indicate your Exam Number on every separate piece of work submitted.
Unless the assessment specifies a group submission, you should assume all submissions are
individual and therefore should be your own work.
All assessment submissions are subject to the Department’s policy on plagiarism and, wherever
possible, will be checked by the Department using Turnitin software.
Submission is via [VLE] and is due by 12:00 noon on Monday 15th August 2022. Please try
and submit early as any late submissions will be penalised.
University of York
Department of Electronic Engineering
C Programming for MSc (ELE00107M)
Assignment 2021/22
Introduction
It is important for engineers to follow a structured process when developing software. A
structured approach to software engineering helps to ensure that the software produced is of high
quality. An important part of this approach is the careful documentation of each stage of the
process in the form of a report. This assignment gives you practice in software development and
report writing for software engineering. Treat the task you have been given as a set of
requirements; you could imagine that they have been given to you by a client. If you feel that the
requirements are unclear, you may make realistic assumptions as necessary; however, you must
make sure that you document these assumptions carefully.
You are required to complete the task using the C Programming Language for a PC running the
Microsoft Windows operating system (i.e. the language and type of computer that you have been
using in the laboratories).
Assignment Structure
IMPORTANT: We have a policy of marking anonymously. Do not identify yourself in your
report or your programs. Use only your student Examination number. Make sure that your
examination number is printed on your report (first page).
Your report should document the development process that you have been through, leading up to
the creation of a piece of software. This should correspond to the development model that you
have covered in the lectures and is detailed in the labscripts. Your report should consist of no
more than 12 pages (minimum font size 10 point), including diagrams and figures.
Your submission should contain:

  1. The Requirements that were given to you;
  2. Your Analysis of the problem, and any assumptions you feel you will have to make;
  3. A Specification for your software that you have derived from your analysis of the
    requirements;
  4. Documentation of the Design process you have used.
  5. Documentation covering how your program is structured into source files and any changes
    you made from the design as originally stated in your specification. You should justify any
    University of York 23/09/2021
    changes to your design that you made during the implementation. This should take the form
    of an Implementation Report.
  6. Documentation of the Testing and Verification process that your went through to ensure
    that your program executes as you required;
  7. A simple User Manual.
  8. Source programs.
    University of York 23/09/2021
    Submitting your work
    You are expected to submit your work electronically using the web links provided on the course
    web page. You must use the assignment project available from the course web page (see the
    section SUBMITTING YOUR ASSIGNMENT).
    You will be expected to link your source code files (files ending in .c and .h) with the assignment
    project. An explanation of how to do this is given on the course web page under the heading
    BLANK ASSIGNMENT PROJECT. It is your responsibility to ensure that you have submitted
    all the files your program needs to be successfully compiled into an executable program. If your
    program cannot be compiled you may receive no marks for program execution.
    Your assignment project MUST work in Windows.
    Your assignment report must be a .pdf file. Please place this in the folder containing your
    assignment project (i.e. it should be located in the same directory as the file assignment.cbp).
    Once you have tested your program and have finished your report make sure everything is in your
    assignment folder. Please zip up the folder containing your project and report. Your zipped file
    should be called assignment.zip.
    Please submit your work in good time before the deadline to ensure that it is uploaded before the
    deadline (note the server might be busy very close to the deadline).
    If you submit multiple versions of the assignment project, the markers will only take the last
    submitted version. If this version is submitted after the deadline then marks will be deducted for
    lateness.
    For your guidance, marks will be awarded as follows:
    ● Requirements, Analysis and Specification — 15%;
    ● Design — 20%;
    ● Implementation of Program — 25%;
    ● Testing and Verification and User Manual — 12%;
    ● Maturity, consistency, presentation and innovation — 13%;
    ● Execution of program — 15%.
    (Total 100%)
    Important
    You should be aware of the University regulations on academic misconduct before completing
    this assignment — any failure to correctly acknowledge work of others will be regarded as
    academic misconduct. This includes the use of solutions provided by module/lab leaders. Thus, if
    you use these, you must make clear which parts of your programs were copied or adapted from
    other sources and where these sources can be found (i.e. the web address). Comments should be
    made in your C code about this.
    University of York 23/09/2021
    Introduction
    The laboratories introduced you to some simple two-dimensional graphical output based on basic
    physics. In this assignment you will take the principles you have met in the labs and develop them
    to create a playable computer game.
    The Task
    You are required to design and implement a computer game which is based on the javelin throw
    track and field event (see: https://en.wikipedia.org/wiki/Javelin_throw). As the player, you
    control the force and elevation with which the javelin is projected across the field, after gaining
    momentum by running within a predetermined runway area. The aim is to throw the javelin as far
    as possible, accounting for other factors, such as the effects of wind. The game must take account
    of the following:
    ● the flight of the javelin must be subject to the effect of gravity;
    ● the distance the javelin is thrown is used to calculate a score;
    ● that the javelin was thrown whilst the thrower was still within the predetermined runway
    area – otherwise the throw is invalid;
    ● that the user can control:
    o the speed at which the thrower runs
    o the angle at which the javelin is thrown
    o when to release (throw) the javelin
    ● the game should keep a score of play over 6 throws;
    ● incorporating sound into the game;
    ● making use of both the mouse and keyboard to control the game.
    The game must be enjoyable and playable for someone who is not experienced with computers
    but rewarding and challenging.
    You might like to think about:
    ● adding a multi-player option;
    ● adding a simulated (computer) competitor.
    ● ensuring that the game is not too frustrating to play — for example, give the player a
    practice session and give hints on how to improve the throw.
    Think about how to incorporate sound into your game. To achieve this, you can use the
    functionality provided by the amio lib. In particular, you could use a call back design to supply
    real-time audio to your application (e.g. sound of the wind, the flight of the javelin and cheers of
    the crowd). Some good examples on how to achieve something like this can be found in the audio
    example ?les (audio01.c and other examples).
退出移动版