共计 19271 个字符，预计需要花费 49 分钟才能阅读完成。
本文是 RT-Thread 用户 @chengjili 原创公布，是用于加入 RT-Thread 与国民技术联手推出 N32G457 RT-Thread 设计大赛，原文：https://club.rt-thread.org/as…
本设计是用来加入《翻新“芯”引擎 | 国民技术 N32G457 RT-Thread 设计大赛》的作品。初衷是因为做军品要求国产化，所以最近也始终在测试国内不同厂家的 32 芯片的性能以及开发便捷性和最重要的稳定性等问题。之前也始终在用 RTT 做开发。浏览官网的时候发现有这个较量，就顺便加入一下。至于做什么，必定不能做我工作上的货色，都是军品窃密的。只能想一些简略的。正好想到平时测试，特地是外出测试，常常因为电源问题而苦恼。于是想做一款繁难的可调电压源，这样只须要带一个充电宝，就能够输入 1~35V 的电压，峰值电流根本能达到 5A 以上。也就能够驱动大多数的设施了。当然，功耗大的设施须要大充电宝能力工作工夫长一些，但至多解决了供电电压不匹配的问题，能够应急应用了。
因为此较量要求用官网给的外围板做开发，所以打算先简略实现一下主体性能。前面再具体做板实现整体性能。这次的测试硬件如下图，N32 的最小零碎板加一块我这边做其它测试的板子。这块板子只用了 LTC3780 局部的电路。
具体电路如下图：
其中 TEC- 对地就是最终的电源输入接口，TEC_DAC 为输入电压调整端口，接 N32 板的 PA4 引脚。TEC_i 为输入电流检测端口，接 N32 板的 PC1 引脚。电源输入对地飞了个 110K 和 10K 的分压电阻，分压短点接 N32 板的 PC0 引脚，用于测量输入电压值（临时没有对测量电压进行标定）。
测试版没有做显示界面（不太想飞线接屏了🤣）。取而代之的是 shell 界面。设置电压和电流值也用的 shell 命令。前面做电路的时候再改成显示屏和按键以及编码器旋钮的交互。测试界面如下：
具体实现了 shell 命令批改电压值，电流值。输入电压和电流反馈的 ADC 采集。实时显示以后输出功率。PID 管制输入电压值。电流超过电流设置值时触发限流爱护，升高电压。按特定波形输入电压的性能，临时只做了正弦信号的。这个性能后续有需要再持续扩大其它信号。
程序方面，自认为 RTT 自带的一些驱动，效率不是很高，只适宜特定场合的简略应用，或者算是提供了一个 demo。实现具体性能的话，倡议本人重写底层驱动。比方这次用的 shell 底层串口驱动框架和 ADC 驱动框架。我日常应用，大多数都是用其它零碎板通过 shell 命令配置以后板子的各运行参数，这样比起人手输出命令，传输数据量就要高很多。底层解决效率低的话就会呈现丢数据，丢指令和串口配置参数的时候 CPU 占用率过高的问题，所以要适应这种场合我都是要重写底层驱动，退出收发 FIFO。读写都只对软件的 FIFO 接口，不必期待硬件的真正的发送和接管实现，进步了代码执行效率。但这次的测试性能，都是人手输出 shell 命令，所以这部分驱动我没有再改变，就用的原有的，针对于这种测试需要倒是足够了。但加入较量，总要在代码上有点奉献，所以这次次要改变的是 ADC 的底层驱动，退出了集体在工作中对 ADC 应用的一些不成熟的了解，心愿能帮忙到有须要的敌人。上面做具体阐明：
如下是官网驱动，enable ADC 通道和读 ADC 数据的代码：
static rt_err_t n32_adc_enabled(struct rt_adc_device *device, rt_uint32_t channel, rt_bool_t enabled)
{
ADC_Module *n32_adc_handler;
ADC_InitType ADC_InitStructure;
RT_ASSERT(device != RT_NULL);
n32_adc_handler = device->parent.user_data;
n32_msp_adc_init(n32_adc_handler);
ADC_InitStruct(&ADC_InitStructure);
ADC_InitStructure.WorkMode = ADC_WORKMODE_INDEPENDENT;
ADC_InitStructure.MultiChEn = DISABLE;
ADC_InitStructure.ContinueConvEn = DISABLE;
ADC_InitStructure.ExtTrigSelect = ADC_EXT_TRIGCONV_NONE;
ADC_InitStructure.DatAlign = ADC_DAT_ALIGN_R;
ADC_InitStructure.ChsNumber = 1;
ADC_Init(n32_adc_handler, &ADC_InitStructure);
/* ADCx regular channels configuration */
ADC_ConfigRegularChannel(n32_adc_handler, n32_adc_get_channel(channel), 1, ADC_SAMP_TIME_28CYCLES5);
if (((n32_adc_handler == ADC2) || (n32_adc_handler == ADC2))
&& ((n32_adc_get_channel(channel) == ADC_CH_16) || (n32_adc_get_channel(channel) == ADC_CH_18)))
{ADC_EnableTempSensorVrefint(ENABLE);
}
/* Enable ADCx */
ADC_Enable(n32_adc_handler, ENABLE);
/* Start ADCx calibration */
ADC_StartCalibration(n32_adc_handler);
/* Check the end of ADCx calibration */
while(ADC_GetCalibrationStatus(n32_adc_handler));
if (enabled)
{
/* Enable ADC1 */
ADC_Enable(n32_adc_handler, ENABLE);
}
else
{
/* Enable ADCx */
ADC_Enable(n32_adc_handler, DISABLE);
}
return RT_EOK;
}
static rt_err_t n32_get_adc_value(struct rt_adc_device *device, rt_uint32_t channel, rt_uint32_t *value)
{
ADC_Module *n32_adc_handler;
RT_ASSERT(device != RT_NULL);
RT_ASSERT(value != RT_NULL);
n32_adc_handler = device->parent.user_data;
/* Start ADCx Software Conversion */
ADC_EnableSoftwareStartConv(n32_adc_handler, ENABLE);
/* Wait for the ADC to convert */
while(ADC_GetFlagStatus(n32_adc_handler, ADC_FLAG_ENDC) == RESET);
/* get ADC value */
*value = ADC_GetDat(n32_adc_handler);
return RT_EOK;
}首先 enable 外面初始化 ADC 就曾经写死了关掉了多通道采集，关掉了间断转换。规定组中也只能退出一个通道。所以，同一时刻只能 enable 一个通道，转换结束后再 enable 下一个通道。每次读取都要使能软件触发转换，而后期待转换实现，而后再读取转换后果返回。这现然不是高效的做法，while 期待的时候 CPU 什么都做不了，也不能调度去执行其它线程的工作。只实用于很偶尔的读取一下 ADC 数据。而大多数读取 ADC 数据根本都是要读取大量数据，做一些平滑滤波或中值滤波，最终失去一些稳固的数据。现然这个框架很难实现此性能，就算勉强用一个线程频繁的去读取 ADC 数据来实现此性能，那预计弱小的 32 芯片也根本干不了别的了。144M 的主频，说高不高，但说低也不低，又有 FPU 能够并行执行一些浮点运算指令，利用好了还是能够实现很多事件的。感觉官网 ADC 驱动框架也根本只限于简略的 demo 应用。于是退出了如下本人的 ADC 驱动程序：
#define ADC1_BUF1_UPDATE_EVENT 0x00000001
#define ADC1_BUF2_UPDATE_EVENT 0x00000002
#define ADC_VREFINT_VAL 1497.89
#ifdef BSP_USING_USER_ADC1
user_adc_config adc1_config =
{
.ADC_Handler = ADC1,
.name = "user_adc1",
.RCC_APB2_PERIPH_GPIOX = RCC_APB2_PERIPH_GPIOC,
.regular_channels = {{ADC_CH_18, RT_NULL, RT_NULL}, //rank1 Vrefint
{ADC_CH_16, RT_NULL, RT_NULL}, //rank2 temp_cup
{ADC_CH_6, GPIOC, GPIO_PIN_0}, //rank3 out_voltage
{ADC_CH_7, GPIOC, GPIO_PIN_1} //rank4 out_current
}
};
uint16_t user_adc1_val_buf[2][USER_ADC1_AVE_N * USER_ADC1_REGULAR_CH];
float adc1_ave_buf[USER_ADC1_REGULAR_CH-1];
rt_thread_t adc_data_handle_thread;
rt_event_t adc_update_event;
#endif
#ifdef BSP_USING_USER_ADC2
user_adc_config adc2_config =
{
.ADC_Handler = ADC2,
.name = "user_adc2",
};
#endif
void AdcDataHandleEntry(void *parameter);
rt_err_t user_adc_init(rt_device_t dev)
{
GPIO_InitType GPIO_InitCtlStruct;
GPIO_InitStruct(&GPIO_InitCtlStruct);
RT_ASSERT(dev != RT_NULL);
ADC_Module *ADCx = (ADC_Module *)dev->user_data;
ADC_InitType ADC_InitStructure;
adc_update_event = rt_event_create("adc_update", RT_IPC_FLAG_PRIO);
if(adc_update_event != RT_NULL)
{adc_data_handle_thread = rt_thread_create("adc_data_handle", AdcDataHandleEntry, RT_NULL, 2048, 1, 10);
if(adc_data_handle_thread != RT_NULL)
rt_thread_startup(adc_data_handle_thread);
}
#ifdef BSP_USING_USER_ADC1
DMA_InitType ADC1_DMA_InitStructure;
if(ADCx == ADC1)
{
/* ADC1 & GPIO clock enable */
RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_ADC1 | RCC_AHB_PERIPH_DMA1, ENABLE);
ADC_ConfigClk(ADC_CTRL3_CKMOD_AHB,RCC_ADCHCLK_DIV8);
RCC_EnableAPB2PeriphClk(adc1_config.RCC_APB2_PERIPH_GPIOX, ENABLE);
ADC_InitStruct(&ADC_InitStructure);
ADC_InitStructure.WorkMode = ADC_WORKMODE_INDEPENDENT;
ADC_InitStructure.MultiChEn = ENABLE;
ADC_InitStructure.ContinueConvEn = ENABLE;
ADC_InitStructure.ExtTrigSelect = ADC_EXT_TRIGCONV_NONE;
ADC_InitStructure.DatAlign = ADC_DAT_ALIGN_R;
ADC_InitStructure.ChsNumber = USER_ADC1_REGULAR_CH;
ADC_Init(ADCx, &ADC_InitStructure);
/* Configure ADC Channel as analog input */
for(int i=0; i<USER_ADC1_REGULAR_CH; i++)
{if(adc1_config.regular_channels[i].channel <= ADC_CH_11)
{GPIO_InitCtlStruct.Pin = adc1_config.regular_channels[i].GPIO_Pin;
GPIO_InitCtlStruct.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitCtlStruct.GPIO_Mode = GPIO_Mode_AIN;
GPIO_InitPeripheral(adc1_config.regular_channels[i].GPIOX, &GPIO_InitCtlStruct);
}
/* ADCx regular channels configuration */
ADC_ConfigRegularChannel(ADCx, adc1_config.regular_channels[i].channel, i+1, ADC_SAMP_TIME_239CYCLES5);
if ((adc1_config.regular_channels[i].channel == ADC_CH_16) || (adc1_config.regular_channels[i].channel == ADC_CH_18))
{ADC_EnableTempSensorVrefint(ENABLE);
}
}
/* Enable ADCx */
ADC_Enable(ADCx, ENABLE);
/* Start ADCx calibration */
ADC_StartCalibration(ADCx);
/* Check the end of ADCx calibration */
while(ADC_GetCalibrationStatus(ADCx));
ADC_Enable(ADCx, ENABLE);
ADC1_DMA_InitStructure.BufSize = USER_ADC1_AVE_N * USER_ADC1_REGULAR_CH * 2;
ADC1_DMA_InitStructure.CircularMode = DMA_MODE_CIRCULAR;
ADC1_DMA_InitStructure.DMA_MemoryInc = DMA_MEM_INC_ENABLE;
ADC1_DMA_InitStructure.Direction = DMA_DIR_PERIPH_SRC;
ADC1_DMA_InitStructure.Mem2Mem = DMA_M2M_DISABLE;
ADC1_DMA_InitStructure.MemAddr = (uint32_t)user_adc1_val_buf;
ADC1_DMA_InitStructure.MemDataSize = DMA_MemoryDataSize_HalfWord;
ADC1_DMA_InitStructure.PeriphAddr = &(ADCx->DAT);
ADC1_DMA_InitStructure.PeriphDataSize = DMA_PERIPH_DATA_SIZE_HALFWORD;
ADC1_DMA_InitStructure.PeriphInc = DMA_PERIPH_INC_DISABLE;
ADC1_DMA_InitStructure.Priority = DMA_PRIORITY_MEDIUM;
DMA_Init(DMA1_CH1, &ADC1_DMA_InitStructure);
DMA_ConfigInt(DMA1_CH1, DMA_INT_HTX | DMA_INT_TXC, ENABLE);
ADC_EnableDMA(ADCx, ENABLE);
DMA_EnableChannel(DMA1_CH1, ENABLE);
NVIC_SetPriorityGrouping(4);
NVIC_EnableIRQ(DMA1_Channel1_IRQn);
ADC_EnableSoftwareStartConv(ADCx, ENABLE);
}
#endif
#ifdef BSP_USING_USER_ADC2
if(ADCx == ADC2)
{
/* ADC2 & GPIO clock enable */
RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_ADC2, ENABLE);
ADC_ConfigClk(ADC_CTRL3_CKMOD_AHB,RCC_ADCHCLK_DIV8);
RCC_EnableAPB2PeriphClk(RCC_APB2_PERIPH_GPIOC, ENABLE);
/* Configure ADC Channel as analog input */
GPIO_InitCtlStruct.Pin = GPIO_PIN_1;
GPIO_InitCtlStruct.GPIO_Speed = GPIO_Speed_2MHz;
GPIO_InitCtlStruct.GPIO_Mode = GPIO_Mode_AIN;
GPIO_InitPeripheral(GPIOC, &GPIO_InitCtlStruct);
}
#endif
return RT_EOK;
}
rt_err_t user_adc_close(rt_device_t dev)
{ADC_Module *ADCx = (ADC_Module *)(dev->user_data);
ADC_Enable(ADCx, DISABLE);
if(ADCx == ADC1)
{DMA_EnableChannel(DMA1_CH1, DISABLE);
NVIC_DisableIRQ(DMA1_Channel1_IRQn);
RCC_EnableAHBPeriphClk(RCC_AHB_PERIPH_ADC1 | RCC_AHB_PERIPH_DMA1, DISABLE);
}
rt_thread_delete(adc_data_handle_thread);
rt_event_delete(adc_update_event);
dev->flag &= ~(RT_DEVICE_FLAG_ACTIVATED);
return RT_EOK;
}
static rt_size_t user_adc_read(rt_device_t dev, rt_off_t pos, void *buffer, rt_size_t size)
{
rt_size_t i;
user_adc_device_t adc = (user_adc_device_t)dev;
float *value = (float *)buffer;
for (i = 0; i < size; i++)
{if(pos+i < USER_ADC1_REGULAR_CH-1)
{value[pos+i] = adc1_ave_buf[pos+i];
}
else {break;}
}
return i;
}
static rt_err_t user_adc_control(rt_device_t dev, int cmd, void *args)
{
rt_err_t result = RT_EOK;
user_adc_device_t adc = (user_adc_device_t)dev;
return result;
}
rt_err_t user_hw_adc_register(user_adc_device_t device, const char *name, const void *user_data)
{
rt_err_t result = RT_EOK;
device->parent.type = RT_Device_Class_Miscellaneous;
device->parent.rx_indicate = RT_NULL;
device->parent.tx_complete = RT_NULL;
device->parent.init = user_adc_init;
device->parent.open = RT_NULL;
device->parent.close = user_adc_close;
device->parent.read = user_adc_read;
device->parent.write = RT_NULL;
device->parent.control = user_adc_control;
device->parent.user_data = (void *)user_data;
result = rt_device_register(&device->parent, name, RT_DEVICE_FLAG_RDONLY);
return result;
}
static int user_hw_adc_init(void)
{
int result = RT_EOK;
/* register ADC device */
#ifdef BSP_USING_USER_ADC1
if (user_hw_adc_register(&adc1_config.n32_adc_device, adc1_config.name, adc1_config.ADC_Handler) == RT_EOK)
{LOG_D("%s register success", adc1_config.name);
}
else
{LOG_E("%s register failed", adc1_config.name);
result = -RT_ERROR;
}
#endif
#ifdef BSP_USING_USER_ADC2
if (user_hw_adc_register(&adc2_config.n32_adc_device, adc2_config.name, adc2_config.ADC_Handler) == RT_EOK)
{LOG_D("%s register success", adc2_config.name);
}
else
{LOG_E("%s register failed", adc2_config.name);
result = -RT_ERROR;
}
#endif
return result;
}
INIT_COMPONENT_EXPORT(user_hw_adc_init);
void DMA1_Channel1_IRQHandler()
{if(DMA_GetIntStatus(DMA1_INT_HTX1,DMA1) == SET)
{rt_event_send(adc_update_event, ADC1_BUF1_UPDATE_EVENT);
DMA_ClrIntPendingBit(DMA1_INT_HTX1, DMA1);
}
if(DMA_GetIntStatus(DMA1_INT_TXC1,DMA1) == SET)
{rt_event_send(adc_update_event, ADC1_BUF2_UPDATE_EVENT);
DMA_ClrIntPendingBit(DMA1_INT_TXC1, DMA1);
}
}
void GetAdcDataAverage(float *ave_buf, uint16_t *adc_buf)
{for(int i=0; i<USER_ADC1_REGULAR_CH-1; i++)
{
float adc_sum=0;
for(int j=0; j<USER_ADC1_AVE_N; j++)
{adc_sum += ADC_VREFINT_VAL * adc_buf[j*USER_ADC1_REGULAR_CH+i+1] / adc_buf[j*USER_ADC1_REGULAR_CH];
}
ave_buf[i] = adc_sum / USER_ADC1_AVE_N;
}
}
void AdcDataHandleEntry(void *parameter)
{
rt_uint32_t recved_event;
while(1)
{if(RT_EOK == rt_event_recv(adc_update_event, ADC1_BUF1_UPDATE_EVENT | ADC1_BUF2_UPDATE_EVENT, RT_EVENT_FLAG_OR | RT_EVENT_FLAG_CLEAR, -1, &recved_event))
{if(recved_event & ADC1_BUF1_UPDATE_EVENT)
{GetAdcDataAverage(adc1_ave_buf, user_adc1_val_buf[0]);
}
if(recved_event & ADC1_BUF2_UPDATE_EVENT)
{GetAdcDataAverage(adc1_ave_buf, user_adc1_val_buf[1]);
}
}
}
} 代码的大略思路是通过调用 rt_device_open 函数关上设施时，通过这里的 Init 函数初始化 ADC，开启 DMA。这里用的每通道的 ADC 数据采集量为 100。利用 DMA 的一半传输实现中断实现双 Buffer 的性能，既传输一半实现后，解决前一半数据，齐全传输实现后处理后一半数据。这样数据处理和 DMA 传输能够并行执行。在 DMA 中断中发送对应的 event。开启一个高优先级线程，梗塞期待 DMA 传输实现事件，别离解决对应的数据。这里没有做中值滤波，只做了简略的均匀滤波。测试了一下，采集 ADC 数据的频率大略是 142 帧 /S。也就是大略 7ms 的工夫出一组通过滤波的 ADC 数据。能够依据需要自行批改采样工夫和均匀点数。我这里打算前面做输入电压调节的 PID 线程用 10ms 的，所以这里管制在了 10ms 内。保障每次做 PID 运算都有新数据。
我用的 ADC 的规定组退出了 4 个通道，第一通道是 CH18，既 Vrefint。第二通道是 CH16，测了一下 CPU 温度，最终是要测量整体电路板的温度，依据电路板温度驱动散热风扇调控降温的。最终是用 CPU 温度调控还是在发热器件旁布一个热敏电阻后续再定。这里因为最小零碎板和电源板离开的，CPU 温度也测不到发热器件的温度。所以也只是简略的采集显示了一下。第三通道是 PC0 引脚，用于采集电压输入的反馈。第四通道是 PC1 引脚，用于采集电流反馈。测试板下面没有做采样电阻，而是用的一个霍尔感应器，量程是±10A 的。所以精度有点差。最终也没必要用这个芯片，打算最终做板还是用采样电阻的计划，N32 又自带运放，间接能够放大输出给 ADC 采集。
具体的 ADC 数据处理，是先依据电源纹波在短暂工夫内差别不大的实践下，对每一次循环采集的 4 通道数据，依据外部基准电压做了个弥补。这样前面依据 ADC 数据计算的电压才是精确的。我这里实测的数据如下图：
数组的 0,4,8,12… 就是保留的实时采集的 Vrefint 的 ADC 数据，而此时的 VrefP 的供电电压是 3.265V。能够计算失去 Vrefint 的理论电压是 1.2068。如下图是官网给的 Vrefint 的电压范畴。
依据理论的 Vrefint 能够推算出 VrefP 供电电压为规范的 3.3V 供电时，Vrefint 的 ADC 转换值为 1497.89。我看默认配置曾经开启了 FPU，所以这里间接用浮点数了，能够进步一点精度。
如下是 main.c 下实现的具体利用代码。比较简单，创立了一个电压控制线程，因为电压调控对于 10ms 的管制周期简直没有滞后性，所以这里的 PID 管制，其实只用了 PI。
#define LED1_PIN 90
#define LED2_PIN 91
#define LED3_PIN 67
#define CPU_Avg_Slope -4.1
#define CPU_V25 1.33
uint16_t test_val=0;
uint8_t print_buf[128];
float read_adc_buf[USER_ADC1_REGULAR_CH-1];
rt_device_t OpenADCDevice(char *name);
rt_device_t adc1_dev=RT_NULL;
rt_device_t dac_dev=RT_NULL;
rt_tick_t shell_getchr_tick;
rt_thread_t voltage_ctrl_thread;
void VoltageCtrlEntry(void *parameter);
void plot_ui()
{rt_kprintf("\033[2J");
rt_kprintf("\033[10;0H");
rt_kprintf("*******************************************\r\n");
rt_kprintf("* voltage:");
rt_kprintf("\033[1;40;31m%s\033[0m","00.00");
rt_kprintf("V *\r\n");
rt_kprintf("* current:");
rt_kprintf("\033[1;40;32m%s\033[0m","0.000");
rt_kprintf("A *\r\n");
rt_kprintf("* power:");
rt_kprintf("\033[1;40;34m%s\033[0m","00.00");
rt_kprintf("W *\r\n");
rt_kprintf("* CPUTemp: 00.00 C *\r\n");
rt_kprintf("*******************************************\r\n");
rt_kprintf("\033[20;0H");
}
int main(void)
{
rt_err_t result;
uint32_t Speed = 500;
/* set LED1 pin mode to output */
rt_pin_mode(LED1_PIN, PIN_MODE_OUTPUT);
rt_pin_mode(LED2_PIN, PIN_MODE_OUTPUT);
rt_pin_mode(LED3_PIN, PIN_MODE_OUTPUT);
adc1_dev = OpenADCDevice("user_adc1");
voltage_ctrl_thread = rt_thread_create("VoltageCtrl", VoltageCtrlEntry, RT_NULL, 2048, 5, 10);
if(voltage_ctrl_thread != RT_NULL)
rt_thread_startup(voltage_ctrl_thread);
plot_ui();
while (1)
{rt_pin_write(LED1_PIN, PIN_LOW);
rt_pin_write(LED2_PIN, PIN_LOW);
rt_pin_write(LED3_PIN, PIN_LOW);
rt_thread_mdelay(Speed);
rt_pin_write(LED1_PIN, PIN_HIGH);
rt_pin_write(LED2_PIN, PIN_HIGH);
rt_pin_write(LED3_PIN, PIN_HIGH);
rt_thread_mdelay(Speed);
}
}
rt_device_t OpenADCDevice(char *name)
{
rt_err_t result;
rt_device_t adc_dev = rt_device_find(name);
if(adc_dev != RT_NULL)
{if(adc_dev->open_flag == RT_DEVICE_OFLAG_CLOSE)
{result = rt_device_open(adc_dev, RT_DEVICE_OFLAG_RDONLY);
if(result == RT_EOK)
{rt_kprintf("%s opened!\r\n",name);
}
else {rt_kprintf("%s open err:%d!\r\n",name,result);
}
}
else {rt_kprintf("%s is already opened!\r\n",name);
}
}
else {rt_kprintf("not find %s device!\r\n",name);
}
return adc_dev;
}
void OpenADC1Device()
{adc1_dev = OpenADCDevice("user_adc1");
}
MSH_CMD_EXPORT(OpenADC1Device, open adc1 device and start adc1 conversion);
rt_err_t CloseADCDevice(char *name)
{
rt_err_t result;
rt_device_t adc_dev = rt_device_find(name);
if(adc_dev != RT_NULL)
{result = rt_device_close(adc_dev);
if(result == RT_EOK)
{rt_kprintf("%s closed!\r\n",name);
}
else {rt_kprintf("%s close err:%d!\r\n",name,result);
}
}
else {rt_kprintf("not find %s device!\r\n",name);
}
return result;
}
void CloseADC1Device()
{CloseADCDevice("user_adc1");
}
MSH_CMD_EXPORT(CloseADC1Device, close adc1 device and stop adc1 conversion);
void ReadADC1Val()
{if(adc1_dev != RT_NULL && adc1_dev->open_flag != RT_DEVICE_OFLAG_CLOSE)
{rt_device_read(adc1_dev, 0, read_adc_buf, USER_ADC1_REGULAR_CH-1);
sprintf(print_buf, "ADC:%f,%f,%f,%f\r\n", read_adc_buf[0], read_adc_buf[1], read_adc_buf[2], read_adc_buf[3]);
rt_kprintf(print_buf);
}
else {rt_kprintf("user_adc1 dev not opened!\r\n");
}
}
MSH_CMD_EXPORT(ReadADC1Val, read adc1 all channel val);
void get_shell_getchr_tick()
{shell_getchr_tick = rt_tick_get();
}
float SetVoltageVal = 5.0; //V
float SetCurrentVal = 3.0; //A
float VoltagePID_P = 100;
float VoltagePID_I = 50;
float user_atof(char *str)
{
float val;
char *ch_p=RT_NULL;
do{if(*str == 0)
return 0;
if(*str == ' ')
{str++;}
else {break;}
}
while(1);
ch_p = strchr(str , '.');
int valH = atoi(str);
float valL=0;
if(ch_p > 0)
valL = atoi(ch_p+1);
do{if(valL >= 1)
{valL /= 10;}
else {break;}
}while(1);
val = valH + valL;
return val;
}
float Sin_vpp=0, Sin_offset=0, Sin_cycle=0, Singal_Cycle_step=0;
void EnSinOut(int argc, char **argv)
{if(argc >= 2)
{if(*argv[1] == '?')
{sprintf(print_buf,"Vpp:%f, Offset:%f, Cycle:%f\r\n", Sin_vpp, Sin_offset, Sin_cycle);
rt_kprintf(print_buf);
}
else if(argc >= 4)
{float val = user_atof(argv[1]);
if(val >=0 && val <=35)
{Sin_vpp = val;}
else {sprintf(print_buf,"Error:Out range[0,35]! Vpp:%fV\r\n", Sin_vpp);
rt_kprintf(print_buf);
}
val = user_atof(argv[2]);
if(val >=0 && val <=35)
{Sin_offset = val;}
else {sprintf(print_buf,"Error:Out range[0,35]! Offset:%fV\r\n", Sin_offset);
rt_kprintf(print_buf);
}
val = user_atof(argv[3]);
if(val >=1 && val <=100)
{
Sin_cycle = val;
Singal_Cycle_step = 2*3.1415926/100/Sin_cycle;
}
else {sprintf(print_buf,"Error:Out range[1,100]! Cycle:%fS\r\n", Sin_cycle);
rt_kprintf(print_buf);
}
sprintf(print_buf,"Vpp:%fV, Offset:%fV, Cycle:%fS\r\n", Sin_vpp, Sin_offset, Sin_cycle);
rt_kprintf(print_buf);
}
else {rt_kprintf("EnSinOut [vpp offset cycle]\r\n");
}
}
else {rt_kprintf("EnSinOut [vpp offset cycle]\r\n");
}
}
MSH_CMD_EXPORT(EnSinOut, enable sinusoidal signal out);
void SetVoltage(int argc, char **argv)
{if(argc >= 2)
{if(*argv[1] == '?')
{sprintf(print_buf,"SetVoltageVal:%f\r\n", SetVoltageVal);
rt_kprintf(print_buf);
}
else {float val = user_atof(argv[1]);
if(val >=0 && val <=35)
{
Sin_vpp = 0;
SetVoltageVal = val;
sprintf(print_buf,"SetVoltageVal:%f\r\n", SetVoltageVal);
rt_kprintf(print_buf);
}
else {sprintf(print_buf,"Error:Out range[0,35]! SetVoltageVal:%f\r\n", SetVoltageVal);
rt_kprintf(print_buf);
}
}
}
else {rt_kprintf("SetVoltage [val]\r\n");
}
}
MSH_CMD_EXPORT(SetVoltage, set voltage val);
void SetCurrent(int argc, char **argv)
{if(argc >= 2)
{if(*argv[1] == '?')
{sprintf(print_buf,"SetCurrentVal:%f\r\n", SetCurrentVal);
rt_kprintf(print_buf);
}
else {float val = user_atof(argv[1]);
if(val >=0 && val <=5)
{
SetCurrentVal = val;
sprintf(print_buf,"SetCurrentVal:%f\r\n", SetCurrentVal);
rt_kprintf(print_buf);
}
else {sprintf(print_buf,"Error:Out range[0,5]! SetCurrentVal:%f\r\n", SetCurrentVal);
rt_kprintf(print_buf);
}
}
}
else {rt_kprintf("SetCurrent [val]\r\n");
}
}
MSH_CMD_EXPORT(SetCurrent, set current val);
void VoltageCtrlEntry(void *parameter)
{
uint8_t wait_i=0, replot_flag=0, overcurrent_flag=0;
float cpu_temp_ave=0, voltage_ave=0, current_ave=0;
dac_dev = rt_device_find("dac");
uint32_t ch = 1;
int32_t dac_val = 4095;
rt_device_control(dac_dev, RT_DAC_CMD_ENABLE, &ch);
rt_device_open(dac_dev, RT_DEVICE_OFLAG_RDWR);
rt_device_write(dac_dev, ch, &dac_val, 1);
float Voltage_err=0, Voltage_err_old=0, Voltage_err_sum=0;
float CtrlVoltage=0;
float Singal_Cycle_i=0;
rt_thread_sleep(100);
while(1)
{if(adc1_dev != RT_NULL && adc1_dev->open_flag != RT_DEVICE_OFLAG_CLOSE)
{rt_device_read(adc1_dev, 0, read_adc_buf, USER_ADC1_REGULAR_CH-1);
float cpu_temp = (CPU_V25 - read_adc_buf[0] * 3.3 / 4096) * 1000 / CPU_Avg_Slope + 25;
float voltage = read_adc_buf[1] * 3.3 / 4096 * 12;
float current = -(read_adc_buf[2] * 3.3 / 4096 - 1.65)/0.132;
if(current < 0)
current = 0;
if(Sin_vpp > 0.0001) // 使能正弦信号输入
{Singal_Cycle_i = fmod(Singal_Cycle_i + Singal_Cycle_step, 2*3.1415926);
SetVoltageVal = Sin_offset + Sin_vpp / 2 * sin(Singal_Cycle_i);
}
if(current <= SetCurrentVal)
{if(overcurrent_flag)
{if(CtrlVoltage < SetVoltageVal-0.1)
{CtrlVoltage += 0.1;}
else if(CtrlVoltage > SetVoltageVal+0.1)
{CtrlVoltage -= 0.1;}
else {
CtrlVoltage = SetVoltageVal;
overcurrent_flag = 0;
}
}
else {CtrlVoltage = SetVoltageVal;}
}
else {
overcurrent_flag = 1;
CtrlVoltage -= 0.1;
}
Voltage_err = voltage - CtrlVoltage;
if(Voltage_err < 0.1 && Voltage_err > -0.1)
{Voltage_err_sum += Voltage_err;}
if(Voltage_err_old * Voltage_err < 0)
{Voltage_err_sum = 0;}
if(Voltage_err_sum > 2)
{Voltage_err_sum = 2;}
else if(Voltage_err_sum < -2)
{Voltage_err_sum = -2;}
Voltage_err_old = Voltage_err;
dac_val += VoltagePID_P * Voltage_err + VoltagePID_I * Voltage_err_sum;
if(dac_val < 0)
{dac_val = 0;}
else if(dac_val > 4095)
{dac_val = 4095;}
rt_device_write(dac_dev, ch, &dac_val, 1);
cpu_temp_ave += cpu_temp;
voltage_ave += voltage;
current_ave += current;
if(wait_i++ >= 100)
{if(rt_tick_get() - shell_getchr_tick > 5000)
{if(replot_flag)
{plot_ui();
replot_flag = 0;
}
sprintf(print_buf,"%.2f",voltage_ave / 101);
rt_kprintf("\033[11;26H");
rt_kprintf("\033[1;40;31m%s\033[0m",print_buf);
sprintf(print_buf,"%.3f",current_ave / 101);
rt_kprintf("\033[12;26H");
rt_kprintf("\033[1;40;32m%s\033[0m",print_buf);
sprintf(print_buf,"%.3f",voltage_ave / 101 * current_ave / 101);
rt_kprintf("\033[13;26H");
rt_kprintf("\033[1;40;34m%s\033[0m",print_buf);
sprintf(print_buf,"%.2f",cpu_temp_ave / 101);
rt_kprintf("\033[14;26H");
rt_kprintf(print_buf);
rt_kprintf("\033[20;0H");
}
else {replot_flag = 1;}
wait_i = 0;
cpu_temp_ave = 0;
voltage_ave = 0;
current_ave = 0;
}
}
rt_thread_sleep(RT_TICK_PER_SECOND/100);
}
}具体代码，有趣味的敌人能够看一下，我就不一点点介绍剖析了。测试用的，代码写的也比拟随便，也没做正文。心愿能对有须要的敌人提供帮忙。也能够在此基础上再持续优化欠缺代码。前面等上传了演示视频再附上视频地址。祝大家工作学习开心欢快。
正文完
